Tractor

Farming 

26 products

Which product fits the job?

Product What it solves Best for Key spec
5007 Premium Diesel Fuel Additive Injector deposits (IDID), hard cold starts, low ULSD lubricity and sludge filter plugging ULSD and biodiesel to B20 in common rail and traditional diesels, on-road and nonroad 1:1000 maintenance (1.3 oz/10 gal), 1:250 first two tanks
5757 Premium Winter Klenz ID Fuel Additive w/ Ice Check Diesel gelling and fuel icing in winter, hard cold starts and injector deposits (IDID) Winter ULSD and biodiesel to B20 in common rail and traditional diesel engines Treat rate 1:1000 (range 1:2000 to 1:500)
405C Power-Master Plus Premium Diesel Fuel Additive Low cetane diesel, black smoke, and fuel that won't stay clean and stable All diesel engines, on-road and nonroad, plus fuel oil for furnaces Treat rate: 1 gal per 3,000 gal diesel (1:3000)
480M Armor Plate w/ Moly D Ultragard Weak oil film, blow-by, engine wear and high amp draw on electrically driven equipment Motor, gear, hydraulic and compressor oils; heavy duty trucks, farm tractors, excavators Mix ratio: 1:10 in engine oil (1 part 480M to 10 parts oil)
406 Injector Perfector Fouled injectors and intake valves, combustion deposits, gas engine knock, ping and run-on Gasoline engines (any ethanol blend), diesel fuel systems and burner nozzles Treat rate per 20 gal: 12 oz clean-up, 3 oz keep-clean
323 Gin Kleen - Grease Spindle grease that breaks down and runs off under heat, plus wear and rust Late model cotton pickers with spindles designed for grease lubrication NLGI 00 grade, bentonite thickener
623 Spindle Bright Helps prevent spindle lint build-up and moistener pad blockage on cotton pickers Mechanical cotton picker water tanks: spindles, picker bars, pivot studs and bevel gears Mix ratio: 1 quart per 50 gallons of water
327-2 Armor Plate Grease with Moly-D / NLGI #2 Wear, water washout and grease melting on heavy duty bearings, pins and joints All purpose greasing of joints, king pins and bearings on farm and industrial equipment NLGI No. 2, non-melt, Timken OK load 65 lb
327-C Armor Plate Grease with Moly-D / NLGI #3 Grease that melts in high heat, washes out or will not stay put on heavy duty equipment Construction and mining equipment, steel mills and brick plants, above freezing NLGI No. 3, non-melt, Timken OK load 80 lb
357-2 Armor Plate Grease with Moly-D / NLGI #2 Grease that melts in high heat, washes out, or will not pump in sub-freezing weather Ball joints, king pins, fifth wheels, wheel and roller bearings, cranes, drag lines NLGI No. 2, non-melt (no dropping point, ASTM D2265)
532T Seal Saver - Extend Seal Life! Leaking hydraulic seals; prevents seals drying out, shrinking, hardening or cracking Tractor hydraulic-transmission fluid, industrial hydraulic oil and hydraulic oil Treat rate: 5% to 10%, or 15% for significant seal leaks
556 Emerald Shield - Shrouded Open Gear Lubricant Open gear grease that builds up on gears and shrouds and has to be cleaned off Large shrouded open gears, such as those on ball mills with automatic lubrication Viscosity: 16,000 cSt at 40 C, 630 cSt at 100 C
234 Odyssey Motor Oil 3400 / 15W-40 Need a CK-4 15W-40 that limits engine wear, deposit buildup and early oil breakdown Heavy duty 2017+ on-highway and Tier 4 non-road diesels, CK-4 diesels, gasoline engines SAE 15W-40, API CK-4/SN synthetic blend moly oil
229 Odyssey Motor Oil 3000 / 15W-40 Engine wear, deposit buildup and oil breakdown in gasoline and most diesel engines Gasoline and most diesel engines: trucks, buses, tractors, combines, stationary generators SAE 15W-40, API CJ-4/SN
B620 Quick Solve Cleaner Concentrate - Biodegradable Cuts oil, grease and grime so surfaces rinse clean with water Machinery, engines, trucks, drilling rigs, dairy buildings and oily concrete floors 1 oz per gallon of water for building maintenance
555 Armor Plate w/ Moly-D Open Gear Lubricant Grease that washes out, slings off or pounds out of exposed gears, cables and guide rails Slow-moving or stationary open gears, racks, cables and fifth wheels, even underwater NLGI No. 2, non-melt, under 1% water washout
327-1 Armor Plate Grease with Moly-D / NLGI #1 Grease too stiff to pump in freezing weather or through automatic lube systems Automatic lube systems and cold weather greasing of heavy duty bearings and joints NLGI No. 1, non-melt, Timken OK load 65 lb
410 Hi-Flame Fuel Polishing and Tank Cleaning Stabilizer Sludge and water emulsions that clog strainers, nozzles and lines; fuel layering in tanks Diesel, heating oil, No. 4 to No. 6 Bunker and waste oil in tanks, boilers and furnaces Treat rate: 1 gal per 8,000 gal No. 2 fuel (1:8,000)
777 Syn-O-Gen Synthetic Grease w/ Moly-D / NLGI #0 Grease that melts and runs in high heat, stops pumping in the cold, or washes out High speed and freezer bearings, brick and tile kilns, lithographic ovens, arctic service NLGI #0 full synthetic, non-melt, -40 F to 550 F range
311 Blue Max Grease / NLGI # 0 Need a softer EP grease than No. 2 for cold weather pumping and centralized lube systems Centralized lubrication systems, extreme cold service, heavy duty equipment NLGI No. 0 lithium complex EP grease, from minus 25 F
311 Blue Max Grease / NLGI # 1 Need a softer EP grease than No. 2 for cold weather pumping and centralized lube systems Centralized lubrication systems, extreme cold service, heavy duty equipment NLGI No. 1 lithium complex EP grease, from minus 25 F
311 Blue Max Grease / NLGI # 2 Bearing wear at high rpm or heavy load, and grease washing out in wet conditions Heavy equipment, high temperature wheel bearings, high speed and electric motor bearings NLGI No. 2 lithium complex EP, approx. minus 25 to 280 F
3895 Concentrated Fuel Tank Cleaner Sludge, water and corrosion in steel fuel storage tanks and piping Steel diesel, biodiesel, gasoline and ethanol storage tanks; marine fuel systems Shock 1 gal/1,000 gal; quarterly 1 gal/2,000 to 4,000 gal
777 Syn-O-Gen Synthetic Grease w/ Moly-D / NLGI #2 Grease that melts and runs in high heat, stops pumping in the cold, or washes out High speed and freezer bearings, brick and tile kilns, lithographic ovens, arctic service NLGI #2 full synthetic, non-melt, -40 F to 550 F range

Specs are summarized from each product's manufacturer Technical Data Sheet, linked on its product page.

Tractor questions and answers

  • Which Primrose diesel additive should I use in my tractor in winter, 5007 or 5757?

    Use Primrose 5757 Winter Klenz ID for winter diesel: its data sheet lists anti-gel, flow improver and anti-icing additives, none of which appear on the 5007 Power Klenz ID data sheet. Both clean and prevent injector deposits (IDID) and comply with federal low sulfur content requirements for nonroad (off-road) diesel engines. Primrose recommends 1:1000 for routine use of either, though 5007 starts at 1:250 for the first two tanks.

  • What NLGI grade Armor Plate grease should I use on my tractor and farm equipment?

    For general greasing, use an NLGI No. 2 grease such as Primrose 327-2 or 357-2 Armor Plate with Moly-D; both data sheets list farms among their applications. Primrose calls 357-2 a medium No. 2 that still retains excellent pumpability at sub-freezing temperatures, while the 327 data sheet names the softer 327-1 (NLGI No. 1) for subfreezing pumpability and automatic lubrication. Follow the grade your equipment manual calls for.

  • Which 15W-40 motor oil should I use in my tractor, 229 Odyssey 3000 or 234 Odyssey 3400?

    Primrose particularly recommends 234 Odyssey 3400 (API CK-4/SN) for heavy duty diesels burning ultra-low sulfur diesel in Tier 4 non-road and 2017 and newer on-highway engines, and earlier diesels calling for API CK-4 oil. 229 Odyssey 3000 (API CJ-4/SN) is particularly recommended for 2007 to 2016 heavy duty diesels with emission after-treatment. Both are 15W-40 synthetic blends listing tractors and combines among their applications; check your engine manual.

  • What is the difference between 323 Gin Kleen and 623 Spindle Bright for cotton pickers?

    Primrose 323 Gin Kleen is a cotton picker spindle grease, while 623 Spindle Bright is a lubricity concentrate you mix into the picker's water tanks. 323 is an NLGI 00 grease for late model cotton pickers with spindles designed for grease lubrication. Mix 623 at 1 quart per 50 gallons of water or more; Primrose says it helps prevent spindle lint build-up and moistener pad blockage.

  • What should I use to lubricate combine and corn picker chains?

    Primrose 548 Armor Plate with Moly-D chain and cable lubricant lists combines, corn pickers, grain elevators and cotton gins among its applications, and is used on roller, drive, drag, conveyor and other chains, plus sprockets, cables and wire rope. It is made from highly refined lubricating oils, and Primrose says its cohesive and adhesive additives reduce dripping and splattering and make it cling tightly to chains, rollers, pins and links.