Specialty Products

Additional specialty products available.  Please contact us for any product applications not displayed to meet your needs.

21 products

Which product fits the job?

Product What it solves Best for Key spec
5757 Premium Winter Klenz ID Fuel Additive w/ Ice Check Diesel gelling and fuel icing in winter, hard cold starts and injector deposits (IDID) Winter ULSD and biodiesel to B20 in common rail and traditional diesel engines Treat rate 1:1000 (range 1:2000 to 1:500)
327-C Armor Plate Grease with Moly-D / NLGI #3 Grease that melts in high heat, washes out or will not stay put on heavy duty equipment Construction and mining equipment, steel mills and brick plants, above freezing NLGI No. 3, non-melt, Timken OK load 80 lb
3000 Phaser Premium Gasoline Fuel Additive - Prevent and reverse phase separation Water and phase separation in ethanol gas, plus carbon, gum, sludge and varnish deposits Gasoline, marine, diesel and industrial engines, especially those running ethanol gas Maintenance rate: 1:500 (1 part per 500 parts gasoline)
403 Protect O Lube Plus Carbon, gum and varnish buildup, engine acids, sticking valves and moisture in fuel Gasoline, marine, industrial and pre-2007 on-road or pre-2011 nonroad diesel engines Treat rate: 1:300 (1:1000 maintenance, 1:100 cleanup)
406 Injector Perfector Fouled injectors and intake valves, combustion deposits, gas engine knock, ping and run-on Gasoline engines (any ethanol blend), diesel fuel systems and burner nozzles Treat rate per 20 gal: 12 oz clean-up, 3 oz keep-clean
532T Seal Saver - Extend Seal Life! Leaking hydraulic seals; prevents seals drying out, shrinking, hardening or cracking Tractor hydraulic-transmission fluid, industrial hydraulic oil and hydraulic oil Treat rate: 5% to 10%, or 15% for significant seal leaks
480M Armor Plate w/ Moly D Ultragard Weak oil film, blow-by, engine wear and high amp draw on electrically driven equipment Motor, gear, hydraulic and compressor oils; heavy duty trucks, farm tractors, excavators Mix ratio: 1:10 in engine oil (1 part 480M to 10 parts oil)
548 / Primrose Armor Plate w/ Moly D Chain & Cable Lubricant Chain, cable and sprocket wear, rust, chain noise, and lube that drips or flings off Roller, hoist, drive and conveyor chains, sprockets, cables and wire rope Typical viscosity: 2500 SUS at 100 F, 150 SUS at 210 F
MP8 Microbicide for bulk fuel & long term storage - Hazardous Freight Bacteria, fungi and the slime sometimes called algae growing in stored fuel Commercial bulk fuel tanks, diesel generators, boats, farm and construction equipment Treat rate: 1.25 to 2.5 fl oz per 100 gallons of fuel
405C Power-Master Plus Premium Diesel Fuel Additive Low cetane diesel, black smoke, and fuel that won't stay clean and stable All diesel engines, on-road and nonroad, plus fuel oil for furnaces Treat rate: 1 gal per 3,000 gal diesel (1:3000)
555 Armor Plate w/ Moly-D Open Gear Lubricant Grease that washes out, slings off or pounds out of exposed gears, cables and guide rails Slow-moving or stationary open gears, racks, cables and fifth wheels, even underwater NLGI No. 2, non-melt, under 1% water washout
410 Hi-Flame Fuel Polishing and Tank Cleaning Stabilizer Sludge and water emulsions that clog strainers, nozzles and lines; fuel layering in tanks Diesel, heating oil, No. 4 to No. 6 Bunker and waste oil in tanks, boilers and furnaces Treat rate: 1 gal per 8,000 gal No. 2 fuel (1:8,000)
777 Syn-O-Gen Synthetic Grease w/ Moly-D / NLGI #0 Grease that melts and runs in high heat, stops pumping in the cold, or washes out High speed and freezer bearings, brick and tile kilns, lithographic ovens, arctic service NLGI #0 full synthetic, non-melt, -40 F to 550 F range
777 Syn-O-Gen Synthetic Grease w/ Moly-D / NLGI #2 Grease that melts and runs in high heat, stops pumping in the cold, or washes out High speed and freezer bearings, brick and tile kilns, lithographic ovens, arctic service NLGI #2 full synthetic, non-melt, -40 F to 550 F range
311 Blue Max Grease / NLGI # 0 Need a softer EP grease than No. 2 for cold weather pumping and centralized lube systems Centralized lubrication systems, extreme cold service, heavy duty equipment NLGI No. 0 lithium complex EP grease, from minus 25 F
311 Blue Max Grease / NLGI # 1 Need a softer EP grease than No. 2 for cold weather pumping and centralized lube systems Centralized lubrication systems, extreme cold service, heavy duty equipment NLGI No. 1 lithium complex EP grease, from minus 25 F
311 Blue Max Grease / NLGI # 2 Bearing wear at high rpm or heavy load, and grease washing out in wet conditions Heavy equipment, high temperature wheel bearings, high speed and electric motor bearings NLGI No. 2 lithium complex EP, approx. minus 25 to 280 F
3895 Concentrated Fuel Tank Cleaner Sludge, water and corrosion in steel fuel storage tanks and piping Steel diesel, biodiesel, gasoline and ethanol storage tanks; marine fuel systems Shock 1 gal/1,000 gal; quarterly 1 gal/2,000 to 4,000 gal
558 Enviro Blend - Rudder Stalk Grease NLGI #2 Grease washing off wet valves and bearings, or leaving an oil sheen on the water Rudder stalks, valves and bearings in contact with water NLGI No. 2, non-melt dropping point, under 1% water washout
5007 Premium Diesel Fuel Additive Injector deposits (IDID), hard cold starts, low ULSD lubricity and sludge filter plugging ULSD and biodiesel to B20 in common rail and traditional diesels, on-road and nonroad 1:1000 maintenance (1.3 oz/10 gal), 1:250 first two tanks
Tuff Jug Utility Jugs 1.25, 2.5 & 5 Gallon Overfilling and spills when pouring (Auto Stop Spout) and hard-to-check jug liquid levels Water, oils, coolants and compatible cleaning solutions for garage and workshop tasks 1.25, 2.5 and 5 gallon multilayer HDPE utility jugs

Specs are summarized from each product's manufacturer Technical Data Sheet, linked on its product page.